# Wireless Charger Idea

**URL:** <https://forum.rabbitcommunity.tech/t/wireless-charger-idea/188>\
**Category:** creativity hub\
**Created:** [June 3, 2024, 1:10am UTC](https://forum.rabbitcommunity.tech/t/wireless-charger-idea/188 "2024-06-03T01:10:12Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![I\_AM\_CAST](https://sea2.discourse-cdn.com/flex002/user_avatar/forum.rabbitcommunity.tech/i_am_cast/32/213_2.png) [@I\_AM\_CAST](https://forum.rabbitcommunity.tech/u/I_AM_CAST)\
**Post date:** [June 3, 2024, 1:10am UTC](https://forum.rabbitcommunity.tech/t/wireless-charger-idea/188/1 "2024-06-03T01:10:12Z")

</div>

For anyone that has a 3D printer, here’s an idea.  
Get components similar to these images below. Start printing the back side of an r1 case. Once the back side is thick \ firm enough laydown the coil and circuit board on it and continue printing the inside back of it until these components are covered and the inside is all level. Then continue printing the rest of the case. This should sandwich to components permanently into the back of the case. for reference the coil is only 4.1cm long by 2.9cm wide. With the L shaped USB-C connector below it should not stick out of the r1 enough to cause a problem when putting the r1 in your pocket. You can even build the case so that it completely covers the USB port and this connector.

 ![Screenshot 2024-06-02 210450](https://us1.discourse-cdn.com/flex002/uploads/rabbit/original/1X/c9d7bc33877bf33411569ce004e721d7b68165ab.jpeg)  
 ![Screenshot 2024-06-02 210403](https://us1.discourse-cdn.com/flex002/uploads/rabbit/original/1X/0f238b85e75b3d64e7c5afd2ac163cf06b534144.png)

---

<div class="post-metadata">

**Author:** ![justin](https://sea2.discourse-cdn.com/flex002/user_avatar/forum.rabbitcommunity.tech/justin/32/45_2.png) [@justin](https://forum.rabbitcommunity.tech/u/justin)\
**Post date:** [June 3, 2024, 3:43pm UTC](https://forum.rabbitcommunity.tech/t/wireless-charger-idea/188/2 "2024-06-03T15:43:07Z")

</div>

Awesome, could you link these parts? I would be willing to test this out.

---

<div class="post-metadata">

**Author:** ![I\_AM\_CAST](https://sea2.discourse-cdn.com/flex002/user_avatar/forum.rabbitcommunity.tech/i_am_cast/32/213_2.png) [@I\_AM\_CAST](https://forum.rabbitcommunity.tech/u/I_AM_CAST)\
**Post date:** [June 3, 2024, 5:22pm UTC](https://forum.rabbitcommunity.tech/t/wireless-charger-idea/188/3 "2024-06-03T17:22:06Z")

</div>

Justin,  
Keep in mind I just did a quick search and really didn’t dig into specs or other sizes \ formfactors for the coil. But I actually think I got lucky as these will do the job. I was also toying with the idea of creating a wireless charging stand for it so that you can make the coils align exactly how they need to be. Otherwise just throwing in any charging pad will do.

> **[Amazon.com: Acxico 2Pcs Wireless Charger Receiver Module PCBA Board Coil...](https://www.amazon.com/Acxico-Wireless-Charger-Receiver-Universal/dp/B08RDMRZL5)**
>
> Wireless Charger Receiver Module PCBA Board Coil Universal Qi DIYDescription:Fine workmanship and good performance.Easy to connect and use.Use:Replace the wireless charging function with DC 5V wired charging equipment, such as: mobile phone, MP3,...

> **[Amazon.com: xiwai 1.0M USB 2.0 Type-A Male to USB-C Type-C Male Data Flat Slim...](https://www.amazon.com/xiwai-Type-USB-C-Type-C-Cable/dp/B0D5RNQM4X)**
>
> Amazon.com: xiwai 1.0M USB 2.0 Type-A Male to USB-C Type-C Male Data Flat Slim FPC Cable for FPV & Disk & Phone : Cell Phones & Accessories